SPOEL 24VUC 3,5W EX II 2D IP65 STAAL FESTO VACC-S18-K4-1U-EX4ME 562897

MAGNEETSPOEL FESTO VACC-S13-18-K4-3U-EX4ME 562895

MAGNEETSPOEL FESTO VACC-S13-18-K4-1U-EX4ME 562893

MAGNEETSPOEL FESTO VACC-S18-35-K4-1UF-EX4ME 570785

MAGNEETSPOEL FESTO VACC-S18-35-K4-3U-EX4ME 562899

MAGNEETSPOEL FESTO VACC-S18-35-K4-2U-EX4ME 562898

MAGNEETSPOEL FESTO VACC-S13-18-K4-1UF-EX4ME 570784

consisting of connector X9 and shielded terminal for devices up to 24 A.

Expansion card with 14 inputs and 8 outputs can be used in PMCtendo DD4 & PMCtendo DD5 & PMCprotego.

Fieldbus junction box for PMCprimo DriveP (size 1.5 A to 24 A) Interfaces: CANbus, RS 232 and PROFIBUS with termination switch and RJ45 cable to connect the fieldbus junction box to the PMCprimoáC.

suitable for the PMCtendo-DD5/230VAC Type: FZECQU 200x65-66 Performance at 40° C/100 % ED: 300 W Resistance value: 66 OHM Temperature switch 180° C: Signal contact 2A/24VDC (DC11) UL version.

without brake; Feedback system Resolver 2-pole; Mo = 3 Nm Io = 4.12 AUN = 400 V nN = 6000 min-1 Jmot = 2.12 kgcm2.

PMCTENDO AC2.75/0/M/1/2/5/H/3 PILZ 1106442 1106442

Cable for PMCprotego and motor with terminal box Assembled on both sides with connector - Ring cable shoe No. of wires and cross section (4 x 1.5 + (2 x 1.0)) Trailing, length: 15 m.

with brake; Feedback system Resolver 2-pole; Mo = 54.0 Nm Io = 22.0 AUN = 400 V nN = 2000 min-1 Jmot = 331.8 kgcm2.

with brake; Feedback system Hiperface multi-turn Resolution of 4096revolutions with 512 steps each Mo = 0.80 Nm Io = 1.10 A UN = 400 V nN= 6000 min-1 Jmot = 0.35 kgcm2 only suitable for PMC servo controllers(DD5, protegoRead more

Drive-based motion control system With expansion card PMCprimo CStandard bus system: CANopen, PROFIBUS Software option: IEC 61131-3programming, dynamic curve calculation Technical data at 3 x 400 V AC:Continuous output cRead more

Included extension board PMCprimo CBussystems standard: CANopenSoftware option: IEC61131-3 programming Path interpolationyyTechnical Detailsat 3 x 400 V AC supply voltage:Permanent output current: 1,5 A;Imax (2 sec.) = 4Read more

Drive-based motion control system With expansion card PMCprimo CStandard bus system: CANopen Software option: none Technical data at 3x 400 V AC: Continuous output current: 12 A, Imax (5 s)= 24 A, powerconsumption in S1 Read more

Drive-based motion control system With expansion card PMCprimo CStandard bus system: CANopen Software option: IEC 61131-3 programmingTechnical data at 3 x 400 V AC: Continuous output current: 12 A, Imax(5 s)= 24 A, powerRead more

Included extension board PMCprimo CBussystems standard: CANopen / ProfibusSoftware option: IEC61131-3 programmingyyTechnical Detailsat 3 x 400 V AC supply voltage:Permanent output current: 1,5 A;Imax (2 sec.) = 4,5 A; ImRead more

Drive-based motion control system With expansion card PMCprimo CStandard bus system: CANopen, PROFIBUS Software option: IEC 61131-3programming Technical data at 3 x 400 V AC: Continuous output current:12 A, Imax (2 s)= 3Read more

Drive-based motion control system With expansion card PMCprimo CStandard bus system: CANopen Software option: IEC 61131-3 programmingTechnical data at 3 x 400 V AC: Continuous output current: 1.5 A, Imax(2 s)= 4.5 A ImaxRead more